Welcome to the Free Talk Live bulletin board system!
This board is closed to new users and new posts.  Thank you to all our great mods and users over the years.  Details here.
185859 Posts in 9829 Topics by 1371 Members
Latest Member: cjt26
Home Help
+  The Free Talk Live BBS
|-+  Profile of yanni cash
| |-+  Show Posts
| | |-+  Messages

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - yanni cash

Pages: [1]

changed C10 out with an 820 pf. oscillator was havin difficulty firing up right.
getting 1/4 watt out of a 2n3053 with 30 turns in T50-2 in L1, and 1800pf caps in both filter cap slots. im thinkin this is not enough for this transmitter, so the next culprit im attacking in the leading filter cap, possibly a higher capacitance is needed there. the 2n3053 is usually good for between 1/2 and 1 watt on HF bands, and in some exceptional cases if you get an old school one, you can get up to about 2 watts of carrier. so there you have it, i did most of the brainwork for ya, if you bought one of these turds and still have the PCB, i'd like to see what you can do. (for educational use only, not my fault if your dumb ass gets a knock from the radio police)

so, i had this AM-1 board which has long since stripped of its parts for other projects, save for a few resistors and caps. ive tried getting the original design to work decent for a little bit and then stripped it all. this board has been put away wet more times than my prom date which is evident by how much rosin gunk has built up over the joints. it was a mess, 5 channels of my music in the x-band, distortion, drifting, all the stuff you DONT want the transmitter to do. so i stripped the board bare and started over. the final/modulator is more or less based off of the corsette which can be found at: freeradiotx.blogspot.com/

1st thing i built was the oscillator around a 1700 khz crystal and a 2n4401.

C10 680pf
C9 100pf
C6, C7 .01
R6 22K
C8 jumper
R7 jumper
R11 1K
L2 crystal
Q6 2n4401
jumper from emitter of Q6 to emitter of Q5 (i did this underneath the board)

now the fun part. the series modulator/final based around an LM386, TIP41, and NTE128 (bfy51 equiv.) the LM386 is mounted in an 8 pin socket which is hot glued to the top of the PCB along the edge where R4, C11, and C3's place was.

R12 50k
R5 100k
R2 jumper "hot" side to pin 6 of LM386
C1 560 ohm resistor
C2 1uf
C4 10uf
Q2 emitter pin jumpered to pin 7 of LM386
Q2 base pin jumpered to pin 3 of LM386
Q2 collector jumpered to pin 5 of LM386
R6 ground side of R6 jumpered to pins 2 and 4 of LM386
Q1 TIP41 (note the different pinout and HEATSINK!)

L1 220uh choke in series with a 22uh choke and 560ohm resistor in mounted in paralell.

R1, on the "cold" side, cut foil trace with razor and make that into an island, jumper this to ground underneath PCB. install .01 cap (103) between the R1 ground island and the other leg of it ugly soldered between the 220 uh choke and the 22uh/560 resitor.


R1, on the "hot" side of R1, put a 33k resistor between that and the side of
R10 connected to the base of Q3.
underneath the pcb solder in a 470 ohm resistor between the base foil trace and ground.
Q3 is an NTE128 or BFY51 (HEATSINK!)

C5 .01
C 13, C 14 1800 pf
L1 4.7uh (31 turns on t-50-2)

misc power supply love:
C15 1000uf
.01 (103) cap between hot lead and ground underneat the PCB

other notes:

in the finals area, i originally tried to use a 2n7000. for you folk out there who like to split hairs on power output, you can use one of these without any gate voltage to speak of and it'll put out a nice crisp signal at around part15 levels. i tried applying around 1.5v to the gate through a 38k resistor and a 1k trimpot. the power was nice, audio good but the trimmer and FET got quite warm. im thinkin if i were to attempt that again, id use a 10k or better pot off of a 5-9 volt regulated source to keep currents in check. over 1.5 volts and you risk destroying the gate. FETs are all about biasing at the end of the day

free radio berkely is bad news. heads up.

Pages: [1]

Page created in 0.018 seconds with 32 queries.